bq769x0

BQ769x0

TIのバッテリ用AFE

The bq78350 is a gauge designed to control the bq769x0 AFE. It has pre-programmed behavior determined by the selection of available parameters. Protection limits can be set in the firmware.
bq78350は、bq769x0AFEを制御するために設計されたゲージです。使用可能なパラメータの選択によって決定される、事前にプログラムされた動作があります。保護限界はファームウェアで設定できます。
The gauging uses a Compensated End of Discharge Voltage (CEDV) algorithm which uses coefficients calculated from data collection runs with the pack design.
ゲージングは​​、パック設計で実行されたデータ収集から計算された係数を使用する補償放電電圧(CEDV)アルゴリズムを使用します。
Communication to the gauge is through SMBus.
ゲージへの通信はSMBusを介して行われます。
The gauge handles all communication to the AFE and does not share the I2C bus to the AFE or allow modification of the AFE registers.
ゲージはAFEへのすべての通信を処理し、AFEへのI2Cバスを共有したり、AFEレジスタの変更を許可したりしません。
The bq78350 is a 2.5-V device and at its initial release supports the -00 and -01 2.5-V output AFEs, be sure to check the latest bq78350 information for options supported.
bq78350は2.5Vデバイスであり、最初のリリースでは-00および-01 2.5 V出力AFEをサポートしています。サポートされているオプションについては、最新のbq78350情報を確認してください。
A customer provided MCU can be used with the AFE.
お客様が用意したMCUをAFEで使用できます。
This allows the MCU programming to provide special system behaviors for the battery.
これにより、MCUプログラミングでバッテリーに特別なシステム動作を提供できます。
The MCU must set the protection registers, enable FETs, recover from faults, and provide a balancing algorithm, if desired.
必要に応じて、MCUは保護レジスタを設定し、FETを有効にし、障害から回復し、バランシングアルゴリズムを提供する必要があります。
The MCU can implement a gauging algorithm and provide display or communication appropriate for the battery system.
MCUは、ゲージングアルゴリズムを実装し、バッテリシステムに適した表示または通信を提供できます。
In addition to the cell voltage readings from the AFE the MCU may measure battery voltage for a real-time calibration as described in the bq769x0 datasheet and pack voltage, if desired.
AFEからのセル電圧の読み取りに加えて、MCUは、bq769x0データシートに記載されているように、リアルタイムキャリブレーションのためにバッテリー電圧を測定し、必要に応じて電圧をパックすることができます。
Any of the bq769x0 device options may be used as appropriate for the MCU.
必要に応じて、bq769x0デバイスオプションのいずれかをMCUに使用できます。
Related to the MCU is the selection of a boot method for the AFE.
MCUに関連するのは、AFEの起動方法の選択です。
The bq769x0 datasheet shows a simple concept of using a switch to boot the device when ready.
bq769x0データシートは、準備ができたらスイッチを使用してデバイスを起動するという単純な概念を示しています。
If the MCU is powered from a separate regulator, it can put the AFE to sleep and boot the AFE as desired.
MCUに別のレギュレータから電力が供給されている場合は、AFEをスリープ状態にして、必要に応じてAFEを起動できます。
With the bq78350, a circuit to provide a pulse is needed to boot the AFE and start the bq78350.
bq78350では、AFEを起動してbq78350を起動するために、パルスを供給する回路が必要です。

  • bq769x0.txt
  • 最終更新: 2021/07/11
  • by yuqlid